Search found 269 matches
- Fri Jan 22, 2021 3:32 am
- Forum: 906 Paso
- Topic: fuel gauge bounces
- Replies: 1
- Views: 14697
Re: fuel gauge bounces
I had the same issue with mine, when the fuel level got down to near half the needle on the gauge would bounce or drop to empty. The issue I found was with the fuel level sender it the tank. The wiper arm in the sender unit wasn't making contact with the coil in the middle. I just bent the wiper arm...
Re: Fuel pump
That one is suitable for fuel injection like what’s on the the 907. You need one that’s for a carby like these: https://www.ebay.com.au/itm/123520630798
https://www.ebay.com.au/itm/321698999506
https://www.ebay.com.au/itm/321698999506
- Mon Jun 01, 2020 8:14 am
- Forum: 906 Paso
- Topic: New Member from Yorkshire, UK
- Replies: 3
- Views: 19810
Re: New Member from Yorkshire, UK
Welcome. There’s plenty of info here and most issues covered.
- Mon Jun 01, 2020 8:09 am
- Forum: 750 Sport and 900SS
- Topic: brake/clutch fluid resistant paint
- Replies: 32
- Views: 49118
Re: brake/clutch fluid resistant paint
+1 for the calliper paint. Used it on mine 9 years ago and they still look good. As Gerhard said you have to bake it on as per the instructions.
- Tue Oct 08, 2019 11:19 am
- Forum: 906 Paso
- Topic: Sprocket cover interchangeable?
- Replies: 7
- Views: 20173
Re: Sprocket cover interchangeable?
The Paso 906 here has the clutch slave cylinder on the right. So, a Paso 750 sprocket cover should be OK. Thank you for the info. A Paso 750 cover may not fit on the 906 engine. While the 906 has the slave cylinder fitted to the clutch cover it utilises the same engine cases as the 907 and 851 whic...
- Tue Oct 08, 2019 11:06 am
- Forum: 906 Paso
- Topic: Paso consumable parts in Australia?
- Replies: 1
- Views: 12633
Re: Paso consumable parts in Australia?
Try Ian Gowanloch
iangowanloch@bigpond.com
Ph 02 69462626
or
Road and Race
sales@roadandrace.com.au
02 43 884 211
or
Eurobrit Motorcycles
info@eurobrit.com.au
Ph 03 9432 6886
iangowanloch@bigpond.com
Ph 02 69462626
or
Road and Race
sales@roadandrace.com.au
02 43 884 211
or
Eurobrit Motorcycles
info@eurobrit.com.au
Ph 03 9432 6886
- Tue Oct 08, 2019 10:53 am
- Forum: 906 Paso
- Topic: Timing belts
- Replies: 8
- Views: 20388
Re: Timing belts
Anything special about these, or will any good brand of the correct size be OK? The 906 engine is fitted with the modern round tooth profile pulleys same as the 907, 900ss, 750 & 900 Monster and ST2. As angelix mentioned you have 2 choices, OEM or Exact Fit. I did a quick search and got a few d...
- Thu Jan 03, 2019 7:15 am
- Forum: 750 Paso
- Topic: Broken Neutral Switch
- Replies: 10
- Views: 10670
Re: Broken Neutral Switch
Good outcome 

- Sun Dec 30, 2018 7:44 am
- Forum: 750 Sport and 900SS
- Topic: 89 900 ss mufflerscheers
- Replies: 7
- Views: 11155
Re: 89 900 ss mufflerscheers
No inserts, the brackets are riveted on.HIGHWAY89 wrote: I will see what Gowanlochs can offer , did yours have the 2 insert threads so to use the original hangers on the 900/ 750
Sport? Thanks again and have a good one.
- Sat Dec 29, 2018 11:52 am
- Forum: 750 Sport and 900SS
- Topic: 89 900 ss mufflerscheers
- Replies: 7
- Views: 11155
Re: 89 900 ss mufflerscheers
I think I paid $350 for them, that was about 10 years ago.
- Fri Dec 28, 2018 9:36 am
- Forum: 750 Sport and 900SS
- Topic: 89 900 ss mufflerscheers
- Replies: 7
- Views: 11155
Re: 89 900 ss mufflerscheers
I got these Conti's from Ian Gowanloch, I modified them to fit the Paso, but they were originally for a 750ss. They are straight through design and have a good note to them.
- Fri Dec 28, 2018 9:19 am
- Forum: 750 Paso
- Topic: Vacuum take off screw - WEBER
- Replies: 8
- Views: 9550
Re: Vacuum take off screw - WEBER
Hi Frank
The only spot is either side of the intake manifold just below the carby. You
will have to disconnect the vacuum lines that provide the vacuum signal for
the ignition module. The threads are already M5 so the adapters will screw
straight in.
The only spot is either side of the intake manifold just below the carby. You
will have to disconnect the vacuum lines that provide the vacuum signal for
the ignition module. The threads are already M5 so the adapters will screw
straight in.
- Fri Dec 28, 2018 7:58 am
- Forum: 750 Paso
- Topic: Broken Neutral Switch
- Replies: 10
- Views: 10670
Re: Broken Neutral Switch
I installed a new copper washer on my leaking neutral switch, it just began to snug when the head of the switch broke off. The plunger itself is all that's holding the head to the threads. If I break the head off I think getting the threaded part out of the engine case won't be too bad, but, I fear...
- Sat Jul 01, 2017 12:36 am
- Forum: 907IE
- Topic: Gearbox lever end falling
- Replies: 4
- Views: 12207
Re: Gearbox lever end falling
If possible, grab yourself a ball bearing about 10mm in diameter and use it to flare the rivet end. Place it in a bench vice and tighten it up just enough until there is no more movement in the shaft, don't over tighten it or you risk cracking the lever. Make sure you have the shoulder on the shaft ...
- Thu Jul 30, 2015 12:20 pm
- Forum: 750 Paso
- Topic: How Fix Crack in the Engine block
- Replies: 10
- Views: 11358
Re: How Fix Crack in the Engine block
A good engineering/welding shop will be able to repair that crack unfortunately it means that the motor will need to come out and stripped down to do it properly. Been there done that. 
